1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
|
/***************************************************************************
* Example sketch for the ADS1115_WE library
*
* This sketch shows how you can use the alert pin to compare with limits. I
* have chosen the window mode. You can also try the max limit (traditional)
* mode. You can change the mode with the function setAlertModeAndLimit_V
*
* Further information can be found on:
* https://wolles-elektronikkiste.de/ads1115
*
***************************************************************************/
#include<ADS1115_WE.h>
#include<Wire.h>
#define I2C_ADDRESS 0x48
volatile int interruptPin = 2;
int ledPin = 10;
volatile bool outOfLimit = false;
ADS1115_WE adc(I2C_ADDRESS);
// ADS1115_WE adc = ADS1115_WE(); // Alternative: sets default address 0x48
void setup() {
Wire.begin();
Serial.begin(9600);
pinMode(interruptPin, INPUT_PULLUP);
pinMode(ledPin, OUTPUT);
digitalWrite(ledPin, LOW);
if(!adc.init()){
Serial.println("ADS1115 not connected!");
}
/* Set the voltage range of the ADC to adjust the gain
* Please note that you must not apply more than VDD + 0.3V to the input pins!
*
* ADS1115_RANGE_6144 -> +/- 6144 mV
* ADS1115_RANGE_4096 -> +/- 4096 mV
* ADS1115_RANGE_2048 -> +/- 2048 mV (default)
* ADS1115_RANGE_1024 -> +/- 1024 mV
* ADS1115_RANGE_0512 -> +/- 512 mV
* ADS1115_RANGE_0256 -> +/- 256 mV
*/
adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change paramater to change range
/* Set the inputs to be compared
*
* ADS1115_COMP_0_1 -> compares 0 with 1 (default)
* ADS1115_COMP_0_3 -> compares 0 with 3
* ADS1115_COMP_1_3 -> compares 1 with 3
* ADS1115_COMP_2_3 -> compares 2 with 3
* ADS1115_COMP_0_GND -> compares 0 with GND
* ADS1115_COMP_1_GND -> compares 1 with GND
* ADS1115_COMP_2_GND -> compares 2 with GND
* ADS1115_COMP_3_GND -> compares 3 with GND
*/
adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change paramater to change range
/* Set number of conversions out of limit after which the alert pin will be active
* - or you can disable the alert (including conversion ready alert)
*
* ADS1115_ASSERT_AFTER_1 -> after 1 conversion
* ADS1115_ASSERT_AFTER_2 -> after 2 conversions
* ADS1115_ASSERT_AFTER_4 -> after 4 conversions
* ADS1115_DISABLE_ALERT -> disable comparator / alert pin (default)
*/
adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); // alternative: ...AFTER_2 or 4. If you disable this sketch dos not work
/* Set the conversion rate in SPS (samples per second)
* Options should be self-explaining:
*
* ADS1115_8_SPS
* ADS1115_16_SPS
* ADS1115_32_SPS
* ADS1115_64_SPS
* ADS1115_128_SPS (default)
* ADS1115_250_SPS
* ADS1115_475_SPS
* ADS1115_860_SPS
*/
//adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default
/* Set continous or single shot mode:
*
* ADS1115_CONTINOUS -> continous mode
* ADS1115_SINGLE -> single shot mode (default)
*/
adc.setMeasureMode(ADS1115_CONTINOUS); //comment or change you want to change to single shot
/* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will
* be active when measured values are beyond the maximum limit or outside the window
* Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
* In max limit mode the minimum value is the limit where the alert pin will be deactivated
* again (if not latched!)
*
* ADS1115_MAX_LIMIT
* ADS1115_WINDOW
*
*/
adc.setAlertModeAndLimit_V(ADS1115_WINDOW, 3.0, 1.5); //you can change modes / limits
/* Enable or disable latch. If latch is enabled the alarm pin will be active until the
* conversion register is read (getResult functions). If disabled the alarm pin will be
* deactivated with next value within limits.
*
* ADS1115_LATCH_DISABLED (default)
* ADS1115_LATCH_ENABLED
*/
//adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default
/* Sets the alert pin polarity if active:
*
* /* Enable or disable latch. If latch is enabled the alarm pin will be active until the
* conversion register is read (getResult functions). If disabled the alarm pin will be
* deactivated with next value within limits.
*
* ADS1115_ACT_LOW -> active low (default)
* ADS1115_ACT_HIGH -> active high
*/
//adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default
/* With this function the alert pin will be active, when a conversion is ready.
* In order to deactivate, use the setAlertLimit_V function
*/
//adc.setAlertPinToConversionReady(); //uncomment if you want to change the default
Serial.println("ADS1115 Example Sketch - uses the Alert Pin / Window Mode");
Serial.println();
Serial.println("Waiting for Value out of Limit");
attachInterrupt(digitalPinToInterrupt(interruptPin), outOfLimitAlert, FALLING);
}
void loop() {
float voltage = 0.0;
if(outOfLimit){
voltage = adc.getResult_V();
Serial.print("Voltage [V]: ");
Serial.println(voltage);
digitalWrite(ledPin,HIGH);
delay(1000);
digitalWrite(ledPin,LOW);
outOfLimit = false;
attachInterrupt(digitalPinToInterrupt(interruptPin), outOfLimitAlert, FALLING);
}
}
void outOfLimitAlert(){
detachInterrupt(2);
outOfLimit = true;
}
|
